亚洲城ca88手机版-官亚洲城会员登录入口-首页

服务热线电话

400-6188-756

亚洲城ca88手机版长时间使用要注意什么?

来源:/ 时间: 2022-05-01 浏览次数: 2

一、功率的选择:
1、 Power selection:
超声波清洗机有时用小功率,花费很长时间也没有清除污垢。而如果功率达到一定数值,很快便将污垢去除。若选择功率太大,空化强度将大大增加,清洗效果是提高了,这时较精密的零件也产生了蚀点,而且清洗机底部振动板空化严重,水点腐蚀也增大,在采用三氯乙烯等有机溶剂时,基本上没有问题,采用水或水溶性清洗液时,易于受到水点腐蚀,如果振动板表面已受到伤痕,强功率下水底产生空化腐蚀更严重,因此要按实际使用情况选择超声功率。
The ultrasonic cleaning machine sometimes uses low power and takes a long time without removing dirt. If the power reaches a certain value, the dirt will be removed soon. If the power is too large, the cavitation intensity will be greatly increased and the cleaning effect will be improved. At this time, the more precise parts also have corrosion spots. In addition, the vibration plate at the bottom of the cleaning machine has serious cavitation and water spot corrosion. There is basically no problem when using organic solvents such as trichloroethylene. When using water or water-soluble cleaning solution, it is easy to be corroded by water spots. If the surface of the vibration plate has been damaged, Cavitation and corrosion are more serious at the bottom of the water under high power, so the ultrasonic power should be selected according to the actual use.
二、频率的选择:
2、 Frequency selection:
超声波清洗机频率从28 kHz 到 120kHz 之间,在使用水或水清洗剂时由空穴作用引起的物理清洗力显然对低频有利,一般使用 28-40kHz 左右。对小间隙、狭缝、深孔的零件清洗,用高频(一般 40kHz 以上)较好,甚至几百 kHz 。对钟表零件清洗时,用 100kHz 。若用宽带调频清洗,效果更良好。
The frequency of ultrasonic cleaning machine ranges from 28 kHz to 120 kHz. When using water or water cleaning agent, the physical cleaning force caused by the action of holes is obviously beneficial to the low frequency. Generally, it is about 28-40 kHz. For parts with small gaps, slits and deep holes, high frequency (generally above 40KHz) is better, even hundreds of kHz. When cleaning clock parts, use 100kHz. If you use broadband FM cleaning, the effect is better.
亚洲城ca88手机版
三、清洗篮的使用 :
3、 Use of cleaning basket:
在清洗小零件物品时,常使用网篮,当频率为 28khz 时使用 10mm 以上的网眼为好。
When cleaning small parts, the basket is often used. When the frequency is 28kHz, it is better to use a mesh of more than 10mm.
四、清洗液温度:
4、 Cleaning fluid temperature:
水清洗液最适宜的清洗温度为 40-6 ,尤其在天冷时若清洗液温度低空化效应差,清洗效果也差。因此有部分清洗机在清洗缸外边绕上加热电热丝进行温度控制,当温度升高后空化易发生,所以清洗效果较好。当温度继续升高以后,空泡内气体压力增加,引起冲击声压下降,效果也会减弱。 有机溶剂清洗液则要接近于沸点的温度来清洗。
The optimum cleaning temperature of water cleaning solution is 40-6, especially in cold weather. If the temperature of cleaning solution is low and the cavitation effect is poor, the cleaning effect is also poor. Therefore, some cleaning machines wrap heating wires around the outside of the cleaning cylinder for temperature control. When the temperature rises, cavitation is easy to occur, so the cleaning effect is good. When the temperature continues to rise, the gas pressure in the cavity increases, causing the impact sound pressure to decrease, and the effect will also be weakened. Organic solvent cleaning solution should be cleaned at a temperature close to the boiling point.
五、清洗液量的多少和清洗零件的位置的确定:
5、 Determination of the amount of cleaning fluid and the position of cleaning parts:
一般清洗液液面高于振动子表面 100mm 以上为佳。由于单频清洗机受驻波场的影响,波节处振幅很小,波幅处振幅大造成清洗不均匀。因此最佳选择清洗物品位置应放在波幅处。 (较有效范围3-18公分)
Generally, the liquid level of cleaning fluid is more than 100mm higher than the surface of vibrator. Because the single frequency cleaning machine is affected by the standing wave field, the amplitude at the wave node is very small, and the amplitude at the wave amplitude is large, resulting in uneven cleaning. Therefore, the best choice for cleaning items should be placed at the wave amplitude. (more effective range: 3-18cm)

联系大家

詹老师:18663767799(微信同号)

陶老师:13011716033(微信同号)

张老师:18663767790(微信同号)

:1476171179/1500705758

:jnkergs@163.com

:地址:济南市先行区太平街道机械装备产业园创业路二号

亚洲城ca88手机版

  • 扫一扫了解更多

  • 扫一扫了解更多

备案号:

亚洲城ca88手机版|官亚洲城会员登录入口

XML 地图 | Sitemap 地图